Home

Home

There are 7 products.

Sort by:
Sales, highest to lowest Relevance Name, A to Z Name, Z to A
Showing 1-7 of 7 item(s)

Active filters

  • Categories: Flow
  • Categories: Pressure
  • Brand: Onicon
  • Brand: Others
  • Brand: RCM
Kalinsky Differential Pressure Transmitter DMG5 In Wall version
Others

Differential Pressure Transmitter DMG5

Kalinsky differential pressure gauge / differential pressure transmitter DMG5 was developed for supervising overpressure of cleanrooms.

A differential pressure sensor range +/- 50 Pa, red LED-display, alarm-lamp, signal horn, analogue output 0-10 V and 4-20 mA for connection with data logger, 2 switching outputs with adjustable threshold value and an additional circuitry to store the alarm message at increasing pressure in the normal range after fall back of the threshold value of the switching output are included.

By using of a red button at the front its possible to reset the alarm message. A software controlled signal damping for display and switching outputs can selected by 10 steps.

Onicon

Electromagnetic Flowmeter FT-3000

ONICON's FT-3000 Series family of Inline Electromagnetic Flow Meters are suitable for measuring electrically conductive liquids in a wide variety of commercial HVAC applications. The FT-3000 series provides analog and digital outputs for flow rate and programmable pulse outputs for flow totalization and/or alarms.

The ONICON FT-3000 Inline Electromagnetic Flow Meters are available in various sizes and arrive factory-configured for ease of installation and start-up. All FT-3000 series flow meters are wet calibrated in a flow laboratory against standards that are directly traceable to international standards. A certificate of calibration accompanies every meter. Typical applications include monitoring of cooling water, heating water, condenser water and domestic water.

  • Highly Accurate
    Individually wet-calibrated with flow measurement accuracy from 0.2% to 0.4% of reading, depending on the transmitter type.

  • Simple Installation and Commissioning
    Each meter is factory programmed and ready for use upon delivery.

  • Low Maintenance
    No moving parts and durable construction provide years of maintenance-free service.

  • Simplified Installation and Commissioning
    Each meter is fully configured and programmed before it leaves the factory and is ready for use upon delivery.
RCM

Liquid Flow Switch

RCM general purpose Flo-Guard II flow switches (liquid) reed switches make or break contacts by detecting the position of a magnet permanently attached to the bellow. Our reed switches can also be ordered for use in hazardous location (Option IS),  when fitted with LED's (Option LED) it provides viewing at a glance when flow rate goes below or above the set point  and makes field calibration easy

RCM

Orifice Flowmeter

The RCM Flo-Gage is a direct reading flow meter with a large, easy to read dial calibrated in engineering units (GPM, SCFM, l/m, etc.) The Flo-Gage measures flow based on a pressure diffential created across a built-in calibrated nozzle. The meter is self-contained and complete, seperate orifices, or blocking, purging or equalizing valves

The Flo-Gage is suitable for measuring water, oil and most other low viscocity liquids which do not deposit out and which are compatible with the materials of construction. The Flo-Gage is also suitable for measuring compressed air, oxygen, carbon dioxide and many other non-toxic compressed gases. (Specify Option I). Saturated steam can also be measured up to 120 psig. (Option K).

SPI Magnetic Flowmeter MM800
Others

SPI Magnetic Flowmeter

Electromagnetic flow meters detect flow by using Faraday's Law of induction.

Inside an electromagnetic flow meter, there is an electromagnetic coil that generates a magnetic field, and electrodes that capture electromotive force(voltage). Due to this, although it may appear as if there is nothing inside the flow pipe of an electromagnetic flow meter, flow can be measured.

SPI Positive Displacement Flowmeter MG Series
Others

SPI Oval Gear Flowmeter

Oval gear flowmeters are categorised as positive displacement flow technology. When liquid flows through this type of positive displacement flowmeter, two oval geared rotors measure a constant volume per rotation within a precisely machined measuring chamber.

With each rotation, a constant volume of liquid is measured. The rotation of the oval gears is sensed via magnets embedded within the rotors. These magnets transmit a high resolution pulse output. The output signal can be process externally via a remote display controller or PLC or via a variety of output/display options available as accessories attached to the flowmeters.

The positive displacement flow technology allows for precise flow measurement of most clean liquids regardless of the media conductivity. Other liquid properties also have a minimal effect on the performance of this type of meter. Flow profile conditioning is not required as with alternative flow technology options making oval gear installations simple to install in tight spaces and at an economical price.

Back to top
back to top