Cart
Custom content

This is custom content

  • Out-of-Stock
    Watanabe Output Isolator TW-2X

Watanabe TW-2X Two-Output DC Signal Isolator

The Watanabe TW-2X converts one DC voltage or current input into two proportional DC outputs for measurement and control systems.

  • Two outputs for connecting compatible receiving instruments.
  • 24 V DC power supply.
  • Accuracy: ±0.1% of full scale.
  • Response time: 50 ms, from 0 to 90%.
  • Compact construction with integrated wiring terminals.

Need advice or a quotation?

Ask Seacom about specifications, availability and the right instrument for your application.

Watanabe TW-2X Two-Output DC Signal Isolator

The Watanabe TW-2X accepts a DC voltage or current signal and provides two proportional DC outputs. It is useful when one measurement signal needs to serve two receiving devices, such as a PLC and a recorder, subject to matching their signal and load requirements.

Powered by 24 V DC, the TW-2X combines the converter and terminal block in a compact unit for instrument-panel installations.

Key Features

  • One DC voltage or current input with two DC outputs.
  • Signal isolation and proportional conversion.
  • Accuracy of ±0.1% of full scale.
  • 50 ms response time from 0 to 90%.
  • Integrated terminal-block construction.

Technical Specifications

SpecificationTW-2X
Input DC voltage or DC current
Output Two outputs; DC voltage/current according to ordering specification
Power supply 24 V DC
Accuracy ±0.1% FS
Response time 50 ms, 0–90%
Dielectric strength 2000 V AC
Dimensions 98 × 48 × 41 mm (H × W × D)
Weight Approximately 130 g
Operating temperature −5 to +50°C
Operating humidity 90% RH or below

FS means full scale. Specify the input range and both output ranges when ordering. Check the applicable load limits and wiring arrangement for the complete model code.

Using One Signal with Two Instruments

A typical arrangement sends one output to the control system and the other to a display or recording device. Both outputs represent the same measured input; this is not a two-input measurement instrument.

ConnectionApplication example
Input DC measurement signal from a compatible transmitter or signal source.
Output 1 Signal to a PLC or controller for process control.
Output 2 Signal to a recorder or indicator for monitoring.

Confirm the required isolation between circuits against the manufacturer’s connection diagram, especially when the receiving devices have different grounding arrangements.

Original Specification Reference — Part 1

Watanabe TW-2X two-output isolator original specification reference part 1

Original Specification Reference — Part 2

Watanabe TW-2X two-output isolator original specification reference part 2

Selection and Ordering

  • Input signal: provide the signal type, minimum and maximum values, and source instrument.
  • Both outputs: identify the signal range and input requirements of each receiving device.
  • Power: confirm that a suitable 24 V DC supply is available.
  • Connections: confirm the required terminal or connector arrangement.
  • Existing installations: include the complete model code and photographs of the label and wiring terminals.

Related Signal Isolators

For applications requiring one output, compare the Watanabe TZ-1XA and TZ-5XA DC signal isolators.

Need Help Selecting a Two-Output Isolator?

Contact Seacom with your input signal, both required outputs and connected equipment. We can help check the configuration for your measurement and control application.

16 other products in the same category:

Anritsu ACSII Temperature Calibrators | Seacom
  • Out-of-Stock

The Anritsu ACSII Series provides controlled temperature sources for checking and calibrating surface and insertion temperature probes.

  • ACSII-1000: surface calibration from 30 to 300°C.
  • ACSII-2000: surface calibration from 30 to 500°C.
  • ACSII-3000: internal calibration from 30 to 500°C.
  • ACSII-4000: surface and internal calibration from 30 to 500°C.
  • PID control with automatic tuning and separate control and calibration units.

Select the model according to probe geometry, required temperature points and calibration requirements.

Yashima Temperature and Universal Controller
  • Out-of-Stock

Yashima's temperature controller and transmitter accepts 15 type of different input from thermocouple, R.T.D. mA & DC voltage. Range setting & alternation can be easy done from thermocouple to R. T. D. or mA to DC voltage. It has programmable scale range and it is so easy that you may program it within few touches!

Tokico MBA Emergency Shut-Off Valve | Seacom
  • Out-of-Stock

The Tokico MBA Series is an electrical signal-operated emergency shut-off valve using a CO₂ cartridge to power the cylinder actuator and close a ball valve.

  • Catalogue connection sizes from 25 to 400 mm.
  • CO₂-powered actuation without a plant compressed-air supply.
  • Electrical triggering through suitable control equipment.
  • Manual reset and horizontal or vertical piping installation.

Contact Seacom to confirm fluid compatibility, pressure, flange specification and control requirements.

Tokico electronic oil flowmeter FRL
  • Out-of-Stock

The Tokico FRL and FRY are high-accuracy electronic positive displacement flow meters for diesel, kerosene, fuel oil, heavy oil, lubricating oil, crude palm oil and other compatible industrial liquids.

The Tokico 75 Series combines direct volumetric measurement with a large LCD display and optional pulse, analogue and alarm outputs for local indication and integration with industrial monitoring systems.

Vaisala MMT310 Moisture in Oil Transmitter | Vaisala Distributor Malaysia | Seacom
  • Out-of-Stock

Vaisala HUMICAP® MMT310 Series provides continuous online measurement of moisture and temperature in transformer, lubrication and hydraulic oils.

The compact transmitter measures water activity (aw) or relative saturation (%RS), showing how close the oil is to forming free water. Optional ppm calculation is available for mineral transformer oil and configured oil types.

  • Models MMT317 and MMT318
  • Water activity range: 0 to 1 aw
  • Temperature range: -40 to +180°C
  • Two configurable analogue outputs and RS-232C
  • Up to 40 bar with MMT318 and ball-valve installation
  • IP66 compact transmitter enclosure
  • Traceable calibration certificates included
Vaisala Indigo520 Supervisor
  • Out-of-Stock

The Vaisala Indigo520 Supervisor manages up to 100 compatible compact humidity and temperature probes through one host unit. It provides local visibility for the maintenance team and Modbus TCP communication for data centre BMS integration.

  • Two daisy chains: Up to 50 probes per chain.
  • 5-inch touchscreen: View measurements, probe status and alerts.
  • Web interface: Supports commissioning and configuration.
  • Malaysia project support: Contact Seacom for probe selection and installation requirements.

Expected availability: early 2027. Enquire with Seacom for configuration and delivery confirmation.

Duct Mounted CO2 Transmitter GMD10
  • Out-of-Stock

The Vaisala GMD110 measures carbon dioxide directly inside ventilation ducts for precise HVAC control and demand-controlled ventilation.

  • CO₂ measurement range from 0 to 10,000 ppm
  • Accuracy of ±40 ppm from 0 to 3000 ppm
  • 4–20 mA, 0–5 V, 0–10 V or Modbus RTU output options
  • Analogue scaling of 0–2000, 0–5000 or 0–10,000 ppm
  • Fast response with less than two minutes to full specification
  • Heated CARBOCAP® sensor head helps prevent condensation
  • IP65 enclosure for demanding duct installations
  • Traceable calibration certificate included
Hyoda AY Series Bimetal Thermometers | Seacom
  • Out-of-Stock

The Hyoda AY Series provides local temperature indication with a stainless steel exterior and IP65 protection.

  • AY4 and AY5 with 100 and 125 mm dials.
  • AY4-QS and AY5-QS with adjustable-angle heads.
  • Available temperature scales within −50 to 500°C.
  • Bimetal indication without a microswitch.
  • Stem and connection selected for the installation.
Sekonic ST-50A Thermohygrograph & Alternatives | Seacom
  • Out-of-Stock

The Sekonic ST-50A displays temperature and relative humidity and records both on a continuous paper chart.

  • Electronic temperature and humidity sensing with LCD display.
  • Optional extension cables for remote sensor placement.
  • Battery operation or a suitable external DC supply.
  • Desktop or wall-mounted installation.

Being phased out: confirm availability before ordering. Alternatives include the Sato Sigma II for paper records, Sato SK-L754 for electronic logging and Vaisala viewLinc for centralised monitoring.

Vaisala HMT330 Transmitter| Indigo500 Replacement
  • Out-of-Stock

The Vaisala HMT330 Series was a flagship industrial transmitter platform for humidity, temperature and calculated moisture parameters. It is discontinued and replaced by an Indigo500 transmitter with the HMP probe selected for the application.

  • HMT331 wall mounting → HMP1 with Indigo500
  • HMT333 ducts and tight spaces → HMP3 or HMP9 with Indigo500
  • HMT334 high pressure and vacuum → HMP4 with Indigo500
  • HMT335 high temperature → HMP5 with Indigo500
  • HMT337 high humidity → HMP7 with Indigo500
  • HMT338 pressurised pipelines → HMP8 with Indigo500
Anritsu VA Clip-Type Temperature Probes | Seacom
  • Out-of-Stock

The Anritsu VA Series uses a clip-type sensing arrangement to measure heat-pipe surface temperature. Select the probe to suit the pipe dimensions and connected instrument.

  • Clip-type design for heat-pipe surface measurement.
  • Published configurations cover −50 to 300°C.
  • Type K and Type E thermocouple options.
  • VA-03, VA-04, VA-05 and VA-06 model options.
Anritsu U Series Moving and Rotating Surface Temperature Probes
  • Out-of-Stock

The Anritsu U Series measures moving and rotating surface temperatures using a low-friction contact design.

  • U-100 and U-200 head-size families.
  • Guard and wheel configurations for different contact conditions.
  • Type K and Type E thermocouple options.
  • Temperature ranges from −50°C to 200°C or 250°C, depending on the configuration.
  • Select the probe geometry, cable and connector to suit the installation.
Vaisala HMT120 and HMT130 Transmitters (Are Being replaced by Origo10) | Vaisala Distributor Malaysia | Seacom
  • Out-of-Stock

The Vaisala HMT120 and HMT130 provide accurate, stable humidity and temperature measurement for cleanrooms, laboratories, data centres and demanding HVAC applications.

Product transition: HMT120/HMT130 are expected to be phased out. For new projects, the Vaisala Origo10 is the recommended replacement platform.

  • Humidity accuracy up to ±1.5% RH
  • HMT120 loop-powered 4–20 mA output
  • HMT130 voltage outputs, RS-485 and relay
  • Interchangeable fixed or remote measurement probe
  • Origo10 recommended for new installations
EDL Pocket-Probe Steel-Cased Thermometer | Seacom
  • Out-of-Stock

The EDL Steel-Cased Pocket-Probe is a portable digital thermocouple thermometer for production, maintenance and laboratory temperature checks.

  • Durable steel housing with a protective cover.
  • Selectable °C and °F display with 0.1° resolution.
  • Available in separate Type K, J, E and T versions.
  • Accepts matching miniature-plug thermocouple probes.
  • Optional peak hold, magnetic backing and Lexan display window.

Probes are sold separately. Match the probe’s thermocouple type and temperature range to the selected instrument.

This website uses cookies to ensure you get the best experience on our website