Cart
Custom content

This is custom content

  • Out-of-Stock
    EDL Ultra Bath Stirred Liquid Calibrator UB

EDL Ultra Bath UB Series Temperature Calibration Baths

The EDL Ultra Bath UB Series provides stirred baths for comparison calibration of immersion thermometers and temperature probes.

  • UB-4010: −40 to 100°C.
  • UB-1020: 50 to 200°C.
  • UB-2050: 200 to 550°C.
  • 18-inch-deep tank with space for multiple suitable sensors.
  • Programmable controller and built-in sensor holding system.

Need advice or a quotation?

Ask Seacom about specifications, availability and the right instrument for your application.

EDL Ultra Bath UB Series Temperature Calibration Baths

The EDL Ultra Bath (UB) Series provides a stirred temperature bath for comparison calibration of immersion thermometers and temperature probes. Its deep tank accommodates multiple sensors, helping laboratories organise calibration work around a shared temperature source.

Three models cover different operating ranges from −40°C to 550°C. Select the bath for your required calibration points; this combined range does not apply to a single model.

Key Features

  • Large bath volume for comparing several suitable sensors at once.
  • 18-inch tank depth for long immersion probes.
  • Stirred medium for temperature stability and uniformity.
  • Programmable controller and built-in sensor holding system.
  • Filling and draining facilities for bath maintenance.
  • iTools software and a NIST-traceable calibration report included by EDL.

Compare Ultra Bath Models

ModelTemperature rangeSelection focus
UB-4010 −40 to 100°C Calibration points below ambient and up to 100°C.
UB-1020 50 to 200°C Intermediate-temperature immersion calibration.
UB-2050 200 to 550°C High-temperature immersion calibration.

The bath medium must suit the selected model and operating temperatures. Confirm the supplied medium and its handling requirements when specifying the system.

Thermometers and Probes

The UB range is intended for suitable bimetal thermometers, liquid-in-glass thermometers, standard platinum resistance thermometers (SPRTs), platinum resistance thermometers (PRTs), RTDs and other immersion probes.

Check the probe's permissible immersion depth, construction and temperature rating. Keep connectors and components that are not designed for immersion outside the bath medium.

Tank and System Specifications

ParameterPublished specification
Inside tank depth 457.2 mm (18 inches)
Access opening 127 × 279.4 mm (5 × 11 inches)
Capacity 42 litres
Wetted parts 304 stainless steel
Resolution 0.01°C
Interface RS-232 and iTools
Published power rating 240 V AC, 25 A, 60 Hz; confirm the required site configuration before ordering.

Display resolution is not calibration accuracy. Bath stability and uniformity depend on temperature and operating conditions; the complete measurement uncertainty also includes the reference instrument and calibration method.

Original Specification Illustration

EDL Ultra Bath UB-4010, UB-1020 and UB-2050 specification comparison

Need Help Selecting a Temperature Calibration Bath?

Contact Seacom with your calibration temperature range, probe types and dimensions, number of sensors and available power supply. We can help review the appropriate UB model and the requirements for your calibration setup.

Product documents

Catalogues, manuals and other files available for this instrument.

UB Catalogue

Ultra Bath Stirred Liquid Calibrator

353.17KB
Download

16 other products in the same category:

High Temperature Probes HHT Series
  • Out-of-Stock

The Anritsu HHT Series is designed for contact measurement of high-temperature surfaces. Select the probe configuration to match your operating temperature, measurement position and thermometer.

  • Type K thermocouple probes.
  • HHT-4 configuration examples: −50 to 800°C.
  • HHT-5 configuration examples: 300 to 1100°C.
  • Different probe configurations to suit access to the measurement point.
Vaisala HMT120 and HMT130 Transmitters (Are Being replaced by Origo10) | Vaisala Distributor Malaysia | Seacom
  • Out-of-Stock

The Vaisala HMT120 and HMT130 provide accurate, stable humidity and temperature measurement for cleanrooms, laboratories, data centres and demanding HVAC applications.

Product transition: HMT120/HMT130 are expected to be phased out. For new projects, the Vaisala Origo10 is the recommended replacement platform.

  • Humidity accuracy up to ±1.5% RH
  • HMT120 loop-powered 4–20 mA output
  • HMT130 voltage outputs, RS-485 and relay
  • Interchangeable fixed or remote measurement probe
  • Origo10 recommended for new installations
Rotating Surface Probe With Flexible Head UX Series
  • Out-of-Stock

The Anritsu UX Series measures the temperature of moving and rotating surfaces. Its flexible head and contact-support mechanism help maintain contact and reduce shaking during measurement.

  • Designed for moving and rotating surface measurements.
  • Flexible head with contact support.
  • Type K and Type E thermocouple options.
  • Published configurations cover −50 to 200°C or −50 to 250°C, depending on model.
Temperature And RH Data Logger (CMS, FDA Approved) DL2000
  • Out-of-Stock

The Vaisala DL2000 combines precision temperature and relative-humidity monitoring with optional analog or door-contact inputs for viewLinc systems.

  • Scheduled for future discontinuation; confirm availability before specifying
  • Current replacement platform: Vaisala VDL200 with suitable smart probes
  • Internal temperature and relative-humidity measurement
  • Optional current, voltage or Boolean input configurations
  • Onboard memory and a typical 10-year battery life
Vaisala HMT140 Replacement with RFL100 | Vaisala Distributor Malaysia | Seacom
  • Out-of-Stock

The Vaisala HMT140 Wi-Fi Data Logger has been discontinued and is no longer recommended for new monitoring systems.

  • Primary replacement: Vaisala RFL100 with AP10 VaiNet Access Point
  • Existing HMT140 installations can continue to be supported
  • Migration should be checked against the existing sensor and input type
  • Contact Seacom for replacement selection and viewLinc compatibility
Anritsu VA Clip-Type Temperature Probes | Seacom
  • Out-of-Stock

The Anritsu VA Series uses a clip-type sensing arrangement to measure heat-pipe surface temperature. Select the probe to suit the pipe dimensions and connected instrument.

  • Clip-type design for heat-pipe surface measurement.
  • Published configurations cover −50 to 300°C.
  • Type K and Type E thermocouple options.
  • VA-03, VA-04, VA-05 and VA-06 model options.
Anritsu SC Series Screw-Mounted Surface Temperature Probes
  • Out-of-Stock

The Anritsu SC Series measures stationary surface temperature using a sensing element secured to the target with a screw.

  • M2, M3, M4 and M5 mounting sizes.
  • Type K and Type E thermocouple options.
  • Temperature ratings from −50°C to 150°C, 200°C, 300°C or 400°C, depending on the model.
  • Select the cable length and connector to suit your installation and instrument.
Anritsu AP-400 & AP-450 Handheld Thermo Printer
  • Out-of-Stock

The Anritsu AP-400 Series combines a high-accuracy thermocouple thermometer with a built-in thermal printer. Measurements can be printed immediately, printed automatically at selected intervals or stored and printed later.

  • Single-channel handheld thermometer with built-in printer
  • Manual, interval and sequential-number printing
  • Stores up to 100 measurements for batch printing
  • AP-400 supports Type E or K with an ASP connector
  • AP-450 supports Type E, K, J, T or R with an ANP connector
  • Thermocouple type is selected when ordering and is not switchable
  • Powered by four AA batteries or an optional AC adaptor

Ask Seacom about the AP-400 Series

Sato SK-1260 Waterproof Digital Thermometer | Seacom
  • Out-of-Stock

The Sato SK-1260 is a handheld digital thermometer with memory and high/low alarms, supporting dedicated thermistor and Type K thermocouple probes.

  • Stores up to 180 readings manually or 120 readings automatically.
  • High and low temperature alarms.
  • MAX/MIN, HOLD and relative-temperature functions.
  • IPX4 protection against water splashes.
  • Probe options for liquids, food, air and surface measurements.
  • Optional printer for stored readings.

Available with the SK-S100K standard probe or as a main unit without a probe. Measuring range depends on the selected probe.

Anritsu BS Needle Temperature Probes | Seacom
  • Out-of-Stock

The Anritsu BS Series needle temperature probes measure internal temperature in liquids and semi-solid materials.

  • Type K and Type E thermocouple options.
  • Probe diameters from 0.9 mm to 5.0 mm, depending on the model.
  • Temperature ranges from −200°C up to 200°C, 300°C or 500°C, depending on the model.
  • Different insertion lengths, cables and connectors to suit the measurement task.
Anritsu SHEATH Series Bendable Temperature Probes
  • Out-of-Stock

The Anritsu SHEATH Series offers bendable sheathed thermocouple probes for measuring temperatures in liquids, air and gases.

  • Grip, sleeve and terminal-box configurations.
  • Sheath diameters from 0.25 to 8.0 mm.
  • Type K and Type E options, depending on configuration.
  • SUS316, SUS310S and Inconel sheath options.
  • Temperature limits depend on diameter, material and coating.
Soldering Iron Probe CR Series
  • Out-of-Stock

Anritsu CR Series temperature probes measure soldering-iron tip temperatures. Select the probe according to the tip diameter and your instrument’s thermocouple input.

  • Measurement range: 0 to 500°C
  • CR-31: for tip diameters below 1.5 mm
  • CR-32: for tip diameters from 1.5 to 4 mm
  • Type K and Type E models
  • CRB base options for connection to compatible thermometers
Fine Flexible Probe SF Series
  • Out-of-Stock

Anritsu SF Series fine flexible temperature probes use extra-fine thermocouple wire in a Teflon-coated sheath for internal temperature measurement.

  • Flexible construction for positioning in restricted spaces
  • Type K and Type E configurations
  • Published temperature range: −50 to 200°C
  • Model references: SF-K-050, SF-K-100, SF-K-150 and SF-K-200
  • Confirm the required length and instrument connector when ordering
Surface Probe with Flexible Head AX Series
  • Out-of-Stock

The Anritsu AX Series measures stationary surface temperature using a flexible head with contact support. This helps the sensing element maintain contact with the target.

  • Flexible head helps reduce errors caused by poor surface contact.
  • Type K and Type E thermocouple options.
  • Published configurations rated to 300°C, 500°C or 800°C.
  • Select the probe geometry, cable and connector to suit your measurement setup.
Sato SK-L200TH II Discontinued | SK-L754 Replacement | Seacom
  • Out-of-Stock

The Sato SK-L200TH II temperature and humidity data logger is discontinued. The replacement is the Sato SK-L754, selected with a compatible temperature and humidity probe.

  • Electronic temperature and humidity recording.
  • 16,000 stored readings per channel.
  • USB communication and microSD data transfer.
  • Choice of plug-in or cabled probe, purchased separately.

View the Sato SK-L754 replacement and probe options.

This website uses cookies to ensure you get the best experience on our website