EDL's Comparison Cryostat Calibrator (CRYO-CAL-2) is the most trusted cryogenic calibration device available on the market. This passively cooled cryostat allows the user to safely and affordably calibrate a range of temperature measurement devices from 77K (-196 °C) up to 0 °C.
Comparison Cryostat Calibrator, Temperature -196 °C (77K) up to 0° EDL's Comparison Cryostat Calibrator (CRYO-CAL-2) is the most trusted cryogenic calibration device available on the market. This passively cooled cryostat allows the user to safely and affordably calibrate a range of temperature measurement devices from 77K (-196 °C) up to 0 °C. Using liquid Nitrogen as the cooling media eliminates the extreme cost of cascade compressor systems and the cumbersome nature of such baths. Calibrating at 113K (-160 °C) is no problem, and in fact, any temperature above 77K (-196 °C) can be accomplished with dwell times greater than 15 minutes. The Cryo-Cal-2 requires no expensive bath fluids and is virtually maintenance free - there are no moving parts or pumping systems. With less than thirteen (13) liters of LN2, affordable comparison calibrations can now be performed at any temperature above 77K (-196 °C)! With our CRYO-CAL-2 you are able to calibrate up to 4 sensors simultaneously in our standard block! The block has (4) 8mm holes to accommodate testing sensors. You may use the holes alone or with the (4) included tubes designed for 0.250". Additional spacer tubes and guides are available for these sizes: 6mm, 0.125", and 0.1875". Custom sizes are available upon request
|
Download |
.
Vaisala high-accuracy immersion temperature transmitter TMI110 is designed for measuring cooling/heating water temperatures in HVAC automation systems. Vaisala TMI110 can also be used for air temperature measurements in air ventilation ducts. The transmitter has a fast response time, enabling precise and reliable control of HVAC systems.
Anritsu MG series probes are temperature sensors designed for stationary surfaces. Built-in magnets allow these probes to be attached to measurement targets. Specific components may be combined to customize products for the needs of a customer's specific application.
Hyoda (Japan) Thermometer with MicroSwitch Model KME-2, KME-4.
It is not just a thermometer, it is a Anritsu thermometer with the built in printer! Linear print system is possible high speed and stuck less. You may printout your temperature data anywhere at anytime! The reliable Anritsu AP-450 series corresponds to your application
AP-450 is replacement of AP-800 (AP-800K, AP-800E, AP-850K, AP-850E) series
Vaisala HUMICAP® Humidity and Temperature Transmitter Series HMD110, HMW110, HMS110 series measure relative humidity and temperature in multiple HVAC applications.
The series includes transmitters for duct mounting HMD110, IP65-classified wall transmitters, and outdoor transmitters with integrated radiation shieldsHMS110.
Vaisala HMD110, HMW110, HMS110 series transmitters are equipped with trusted HUMICAP® 180R sensors. They are individually adjusted and delivered with a calibration certificate. The factory calibration is traceable to NIST.
Transmitters can be field-calibrated using either an HM70 Hand-Held Humidity and Temperature Meter, or a PC connection.
Anritsu Model AT series probes are Air temperature sensors designed to measure the temperature of Air. Specific components may be combined to customize products for the needs of a customer's specific application.
Sekonic ST-50 (ST-50A) is microprocessor based thermohygrograph. Apart from measuring and recording temperature and relative humidity, it also has large LCD display and alarm output. Remote application is applicable with its electronic remote sensor.
Hyoda (Japan) Waterproof Bimetal Thermometer M series
Model: M3, M4, M6
Anritsu AX series are the ultimate sensor for the surface temperature measurement: A series, and enhanced it by fitting it with Flexible head. They are the best suitable for any applications based on philosophy of "Simple is the best" and suit to any of your request.
Vaisala Indigo300 Transmitter is a host device for displaying measurement values from Vaisala Indigo-compatible probes and/or transmitting them to automation systems through analog signals.
At first glance Anritsu U series probe looks simple, but it has many hidden new mechanisms. Frictional heat have a serious adverse effect during measurement of the temperature of the moving surface. The contact-pressure control plate is one of our own techniques to reduce measurement error in such a case. We use a non-fixed support structure to cope with contact friction at the heat-sensing part. Keeping the support in a non-fixed state helps reduce the stress applied to the part, thereby improving durability
Anritsu HR series are high accuracy handheld thermometers by Anritsu meter. The high accuracy is realized by adopted the thermocouple material from input plug to cold junction It has automatic standard voltage calibration system, hence achieved high accuracy, high response and high stability. This is the right tool if you are looking for precise temperature measurement!
EDL's Comparison Cryostat Calibrator (CRYO-CAL-2) is the most trusted cryogenic calibration device available on the market. This passively cooled cryostat allows the user to safely and affordably calibrate a range of temperature measurement devices from 77K (-196 °C) up to 0 °C.
.png)
CryoCal2 Catalogue
- Comparison Cryostat Calibrator CryoCal2
(293.56k)
