Micro Sensor Probe CS Series

Kalinsky differential pressure gauge / differential pressure transmitter DMG5 was developed for supervising overpressure of cleanrooms.

A differential pressure sensor range +/- 50 Pa, red LED-display, alarm-lamp, signal horn, analogue output 0-10 V and 4-20 mA for connection with data logger, 2 switching outputs with adjustable threshold value and an additional circuitry to store the alarm message at increasing pressure in the normal range after fall back of the threshold value of the switching output are included.

By using of a red button at the front its possible to reset the alarm message. A software controlled signal damping for display and switching outputs can selected by 10 steps.

The PDT101 differential pressure transmitter is designed for demanding cleanroom applications. The sensor integrates with the Vaisala viewLinc monitoring system to measure and monitor pressure differentials in regulated environments. Ideal for high performance cleanroom environments in the life science, semiconductor and electronics industries.

Tokico PFA resin series flowmeter has no moving parts, and the parts in contact with liquid are composed by PFA resin, and excellent in corrosion resistant and clean vortex flowmeter

The parts that come into contact with the liquid are made of PFA resin with excellent corrosion resistance, so there are no seals or pockets apart from the parts where pipes are connected. This makes the series suitable for measuring fluids like liquid chemicals, corrosive fluids and ultrapure water.

Anritsu MG series probes are temperature sensors designed for stationary surfaces. Built-in magnets allow these probes to be attached to measurement targets. Specific components may be combined to customize products for the needs of a customer's specific application.

Vaisala Oil Moisture Transmitter MMT330 enables fast and reliable detection of moisture in oil. The MMT330 can be used in on-line moisture monitoring and as a control device, allowing separators and oil driers to be started only when needed. Proper monitoring saves both oil and the environment. With the MMT330 it is easy and economical to monitor the effects of moisture in oil.

For use up to zone 0 and 20

The intrinsically safe Vaisala  HMT370EX is the ideal solution for use in hazardous areas up to zone 0 and 20. In addition to measuring relative humidity and temperature, the transmitter outputs also other humidity parameters: dew point temperature, wet-bulb temperature, absolute humidity, mixing ratio, water concentration, water mass fraction, water vapor pressure, and enthalpy. Special models for moisture in oil and jet fuel measurements are available.

Typical applications include fuel storage tanks, manufacturing of chemicals, pharmaceuticals and food, biogas production' paint booths and any other industry or process where intrinsically safe humidity or moisture in oil measurement is required. 

This next-generation HMT370EX transmitter replaces the long-running HMT360 transmitter series.
The HMT370EX offers several probe options for different applications:

• HMP371 - for wall mounting
• HMP373 - for confined spaces
• HMP374 - for pressurized spaces
• HMP375 - for high temperature
• HMP377 - for high humidity
• HMP378 - for pressurized pipelines

Models for measuring moisture in oil and jet fuel:

• HMP378F - for moisture in oil
• HMP378H - for JET A-1 fuel

RCM general purpose Flo-Guard II flow switches (liquid) reed switches make or break contacts by detecting the position of a magnet permanently attached to the bellow. Our reed switches can also be ordered for use in hazardous location (Option IS),  when fitted with LED's (Option LED) it provides viewing at a glance when flow rate goes below or above the set point  and makes field calibration easy

• FDA 21 CFR Part 11, EU Annex 11 Compliant

The DL1700 thermocouple data loggers provide accurate temperature data acquisition, remote alarming, and continuous monitoring.

The  loggers are ideal for demanding environments that use extreme temperatures, from -240 °C to 1760 °C; applications such as liquid nitrogen (LN2), ovens, sterilization chambers and other extreme temperatures in laboratories and industrial environments.

The loggers connect to Vaisala's viewLinc software to provide historical and real-time data, remote alarming, and reporting in compliance with global regulations and standards.

The Vaisala OPC-DA Server software can be used to integrate Vaisala DL-series data loggers to non-Vaisala systems. If access to historical measurements is needed, the Vaisala OPC-UA Server can be used to integrate the viewLinc database with non-Vaisala systems.

Anritsu HR series are high accuracy handheld thermometers by Anritsu meter. The high accuracy is realized by adopted the thermocouple material from input plug to cold junction It has automatic standard voltage calibration system, hence achieved high accuracy, high response and high stability. This is the right tool if you are looking for precise temperature measurement!

Anritsu CR Series is a temperature probes for the tips of soldering irons. Select the probe type best-suited to the diameter of your soldering iron tip.

Anritsu A series are the ultimate sensor for the surface temperature measurement. They are the best suitable for any applications based on philosophy of "Simple is the best" and suit to any of your request.

*This is replacement probe for N series, it is more durable than ever.

Hyoda (Japan) Waterproof Bimetal Thermometer M series
Model: M3, M4, M6