RCM general purpose Flo-Guard II flow switches (liquid) reed switches make or break contacts by detecting the position of a magnet permanently attached to the bellow. Our reed switches can also be ordered for use in hazardous location (Option IS), when fitted with LED's (Option LED) it provides viewing at a glance when flow rate goes below or above the set point and makes field calibration easy
| Model | Flo-Gard II | |
| Fixed / Portable | Fixed | |
| Tolerance | Maximum temperature: 100 deg C Maximum pressure: 28 bar |
|
| Accuracy | ± 3% FS | |
| Remarks | Enclosure Rating: NEMA 4X / IP66 Electrical Rating: Ambient Temp.: 120ºF (50ºC) Setability: ± 5% F.S. Hysteresis: ± 13% F.S. Contact Rating: 10 Watts 175 Vdc max. 125 Vac max. Current: 350 mA max. switching Hazardous Location Specifications: (Option IS & LED) Contact Rating: Vmax = 28V, Imax = 110mA, Pmax = 1.2W, Ci = 0uF, Li = 0uH CSA / NRTLc: AEx ia IIC: Class I, Division I, Groups A, B, C & D Class II, Division I, Groups E, F & G KEMA: Ex ia IIC: Zone 0, II 1G T4 0°C ≤ Ta ≤ 50°C ATEX EC Type Examination Protect from freezing liquid |
|
.
Ryutai Kogyo Pitot Cell Flowmeter PFT-A is an economic flowmeter that measures large flow rate of water in large pipe. It is suitable for both hot and cold water, installation is easy and has very little pressure loss. In addition, the reading is displayed in liter / min
Ryutai Kogyo Model GTF and ATF is widely used for its high quality and ease of use. This flow meter is in-line type, installed directly in your pipe line, and measure instantaneous flow rate of liquid or gas with high accuracy.
Simple design and rigid construction enable you to check or disassemble the unit without any special knowledge. Besides above feature, you can select the material from our wide variety of materials to meet your specific application.l There are widely used for its high quality and ease of use
The RCM Flo-GageTM is a direct reading flow meter with a large, easy to read dial calibrated in engineering units (GPM, SCFM, l/m, etc.) The Flo-Gage measures flow based on a pressure diffential created across a built-in calibrated nozzle. The meter is self-contained and complete, seperate orifices, or blocking, purging or equalizing valves.
The Flo-Gage is suitable for measuring water, oil and most other low viscocity liquids which do not deposit out and which are compatible with the materials of construction. The Flo-Gage is also suitable for measuring compressed air, oxygen, carbon dioxide and many other non-toxic compressed gases. (Specify Option I). Saturated steam can also be measured up to 120 psig. (Option K).
Aichi Tokei Magnetic Flow Sensors For Liquids with Display
Model NW (Local display type)
Model NW-P (With pulse output)
Aichi Tokei's governors are actively working at various locations for energy-saving, labor-saving on energy control, and providing safe supply of gas.
The ones introduced here are Aichi Tokei's standard governors.
•Governor for high temperature gas
•Governor with the precise adjustment handle
•Governor for gas that contains sulfide
•Other special governors
Ryutai Kogyo Pitot Cell Flowmeter PFT is an economic flowmeter that measures large flow rate of water in large pipe. It is suitable for both hot and cold water, installation is easy and has very little pressure loss. In addition, the reading is displayed in liter / min
TOKICO FLOWMETER, TOKICO OIL FLOWMETER is a high accuracy displacement type flow meter composed of two roots and measures flow directly. Tokico Oil Flowmeter has little deterioration in the instrument accuracy because a couple of roots rotates with non-contact. This flow meter measures with high accuracy and wide flow range.
Compact, self contained Kofloc Mass Flow Meters are designed to read flow rates of gases. The rugged design coupled with instrumentation grade accuracy provides versatile and economical means of flow control.
Aichi Tokei ND Flowsensor is ideal for measuring variety of fluid and outputs open collector pulses with the built-in amplifier type magnetic sensor.
Ryutai Kogyo MCF can be linked with a remote indicator, integrator and recorder A reliable electronic transmitter housed in the aluminum indicator case provides current signals (DC, analog) proportional to measured flow rates for remote instruments.
MCF series are now used in the computer-controlled flow system. Output signals are analog DC current of high linearity and agree with any inputs of remote instruments. Well suited design on applications The body that measures fluid flow has been designed with consideration having been given to many factors such as flow direction, flow rate, pressure, temperature, presence or absence of slurries and accessories required.
The Precisely manufactured transmitter which is enclosed in the indicator case provides reliable output signals.
Kent Elster Helix Woltmann cold water meter can be installed in horizontal, vertical or inclined pipelines without loss of accuracy. This meter not only conforms to relevant BS, ISO and EEC standards, but offers user benefits which greatly exceed these specifications.
TOKICO FLOWMETER, TOKICO OIL FLOWMETER a high accuracy displacement type flow meter composed of two roots and measures flow directly. Tokico Oil Flowmeter has little deterioration in the instrument accuracy because a couple of roots rotates with non-contact. This flow meter measures with high accuracy and wide flow range.
RCM general purpose Flo-Guard II flow switches (liquid) reed switches make or break contacts by detecting the position of a magnet permanently attached to the bellow. Our reed switches can also be ordered for use in hazardous location (Option IS), when fitted with LED's (Option LED) it provides viewing at a glance when flow rate goes below or above the set point and makes field calibration easy
